Desert Boho Tassel Crown: Free Crochet Pattern

Introduction

The Desert Boho Tassel Crown is a quick, cheerful crochet headband that anyone can make, even if you have only just learned single crochet. It is a soft mint tube with a lavender striped band at the front, finished with three tiny two-tone tassels tied along the top edge for a festival-ready boho look. Because it is worked in simple joined rounds, the fabric is dense and stretchy, so it sits comfortably against the head without slipping. It works up in an evening, uses only about 70 yards of yarn, and makes a lovely gift or a last-minute accessory for a concert, market day, or desert road trip.

Materials Needed

• Yarn: Worsted weight (category 4) cotton yarn, approximately 50 yards mint and 20 yards lavender.
• Hook: 5.0 mm (H-8) crochet hook.
• Notions: Stitch marker, tapestry needle, scissors, and a ruler for trimming tassels.
• Finished size: Fits a head circumference of 20-22 inches; headband width is 2 inches.

Abbreviations

• ch — chain: make a loop of yarn over the hook and pull it through.
• sc — single crochet: insert hook, yarn over, pull up a loop, yarn over, pull through both loops.
• sl st — slip stitch: insert hook, yarn over, pull through the stitch and the loop on your hook at once.
• st(s) — stitch(es).
• R — round.

Gauge

16 stitches and 16 rounds = 4 inches in single crochet. To check it, crochet a small swatch in joined single crochet rounds and measure a 4-inch section; adjust your hook size if you have more or fewer stitches than this.

Tips Before You Start

• When you join the starting chain into a ring, check that the chain is not twisted before you work the first round — a twist here cannot be fixed later.
• Use a stitch marker in the first stitch of each round so you always know where to join.
• Keep your single crochet tension even and fairly firm; a dense tube holds its shape and grips the head better.
• Change colors on the last pull-through of the final stitch of the round so the color change looks clean.

Step-by-Step Instructions

Headband (worked in rounds)

With mint, ch 41, join with sl st to first ch to form a ring, being careful not to twist.

R1: Ch 1, sc in each ch around, join with sl st to first sc (40 sc).

R2-4: Ch 1, sc in each st around, join with sl st to first sc (40 sc).

Change to lavender.

R5-6: Ch 1, sc in each st around, join with sl st to first sc (40 sc).

Change to mint.

R7-10: Ch 1, sc in each st around, join with sl st to first sc (40 sc).

Fasten off and weave in ends.

Tassels (make 3)

Cut 3 strands of mint and 3 strands of lavender, each 6 inches long. Hold 1 mint and 1 lavender strand together and fold them in half to create a loop. Insert the hook through the top edge of the headband at the front center, pull the loop through, then pull the yarn ends through the loop and tighten to secure. Repeat for two more tassels, spacing them evenly along the top edge about 1 inch apart. Trim the tassel ends to 1.5 inches.

Assembly and Finishing

The headband is worked in one piece, and the tassels are tied directly onto it, so no sewing is required. Weave in all yarn ends on the inside of the tube with your tapestry needle. Lightly mist or steam block the headband to even out the stitches, then lay it flat to dry. Fluff the tassels and trim any uneven ends so all three hang evenly.

Pro Tips and Variations

• Swap the mint and lavender for any two colors you love, or use a self-striping cotton for a multicolor band.
• Add a fourth tassel or make the tassels longer for a bolder festival look.
• Work a few extra rounds for a wider headband, or fewer for a narrow one — just keep the stitch count at 40 per round.